KP Performance Antennas, an Infinite Electronics brand and a manufacturer of wireless network antennas, has just released a new series of cables with rubber boots that are ideal for installations in tight areas where it is difficult to tape individual connectors. KP’s new line of N-type male and RP-SMA male cables includes seven models with rubber boots to fully cover … [Read more...]
Advanced Test Equipment Corporation and PMM Finalize New Agreement
Advanced Test Equipment Corporation (ATEC) announced the finalized agreement between ATEC and PMM—making ATEC the new United States and Mexico sole distributor and authorized service center for calibrations and repair of PMM equipment. ATEC is a worldwide leader in test equipment rentals, sales, and calibrations, providing companies with EMC and other equipment that meets all … [Read more...]
Transtector Expands Surge Protection Line with Isolation Transformers for Medical Applications
Transtector Systems, an Infinite Electronics brand and an industry-leading provider of end-to-end power and signal integrity solutions, today launched a new series of data isolators optimized for medical applications, providing a highly effective layer of protection that is simple to install. Also known as isolation transformers, these cost-effective components are fully … [Read more...]
KP Performance Antennas Launches New High-Performance, Rugged 900 MHz Omni Antennas
KP Performance Antennas, an Infinite Electronics brand and a manufacturer of wireless network antennas, has just released new 900 MHz Omni antennas that are ideal for utilities, SCADA and two-way communication. KP’s new line of Omni antennas includes two models that operate over the licensed 800 MHz/900 MHz and unlicensed 902-928 MHz ISM bands. These antennas are … [Read more...]
Electromagnetic Pulse: The Myths and Reality
Introduction Some 10-15 years ago this topic was irrelevant for the civil sector, and the issue of protection of electrical and electronic equipment from high altitude electromagnetic pulse (HEMP) solely belonged to military specialists. Today, much of the mass media discusses HEMP danger for civil infrastructure at the global level in all possible ways; and thus, this topic … [Read more...]
AE Techron Introduces Switch-Mode Amplifier Line with a DC-to-50 kHz bandwidth, up to 100 kVA Output
AE Techron, Inc. announces the availability of its new 8500 series amplifier line, a new Class D design that offers high-power operation at frequencies previously unavailable in a switch-mode power amplifier. 8500 series amplifiers feature a DC to 50-kHz bandwidth with a slew rate of up to 60 V/us. Models with a long-term power rating of up to 20 kW (up to 100 kVA of apparent … [Read more...]
Flexibility Key to Trends in EMI Pre-Compliance Debugging
EMI analysis continues to expand as more companies add electronic control and wireless remote capabilities to their products. The need to drive speed and efficiency throughout the design process means these engineers need to conduct EMI pre-compliance testing on the same bench as the debugging embedded and RF signals. Modern instruments often combine debugging and … [Read more...]
EMC Test Equipment Selection and Sizing
Explosive growth in technologies like portable electronics, Internet of Things (IoT) devices, and autonomous vehicles has led to a world full of electromagnetic interference. Efficient EMC testing is more critical than ever, and is dependent on high-quality test equipment. Historically, not a lot of education has been provided on the careful considerations needed for … [Read more...]
Precision Low-Voltage Battery Charger Designed to Operate in Hazardous Locations
The APS BC-6964 Battery Charger is designed for hazardous location applications requiring Class I Div II equipment. The BC-6964 accepts 3-phase 60 Hz AC input and generates 24 VDC 50A nominal output. The charger provides a seamless transition from a voltage source to a current limit operation for optimum battery charging. In voltage mode, the Charger regulates to a factory … [Read more...]
ITG Electronics introduces New Power over Ethernet (PoE) Filters
ITG Electronics, a leading manufacturer of Inductors and Transformers in business since 1963, now offers a range of EMI filters Power over Ethernet applications. The dual-stage filters offer 100 dB attenuation over a wide band, 100 MHZ-10GHz, to reduce EMI and provide clean power to sensitive equipment or sensitive areas such as MRI rooms. PoE is perfect for LED lighting … [Read more...]
- « Previous Page
- 1
- …
- 19
- 20
- 21
- 22
- 23
- …
- 364
- Next Page »
