In aerospace, there is one standard that always seems to be popping up, DO-160. Aircraft suppliers are often complying with aviation authorities’ regulations by testing their product to DO-160. DO-160 is a standard that was published by the industry group Radio Technical Commission for Aeronautics known as RTCA. RTCA is not a government regulation, however the FAA, EASA and … [Read more...]
UNECE Regulation 10: Electronic Sub-Assembly with Immunity Related Functionality
In this special guest-installment for the series of blogs on UNECE Regulation 10, Revision 5, Amendment 1 (8 October 2016), written by Elite Electronic Engineering’s Automotive Test Group Team Leader Stan Dolecki, we will look at electronic sub-assemblies with immunity-related functionality. Electronic sub-assemblies (ESA) utilized in the European Union require conformity … [Read more...]
The Übersystem, Automotive Ethernet: An Interview with Stephen Jackson
With larger bandwidth, lower latency, and lighter weight, this is the Übersystem; it’s the OPEN (One-Pair Ether-Net) Alliance Ethernet for automotive, aerospace and more! On June 12th, 2018 I talked to Stephen Jackson (Steve) of Keysight’s Ixia Solutions Group about why Automotive Ethernet is the best solution for Advanced Driver Assistance Systems, ADAS, power train, body … [Read more...]
Identifying and Locating Radio Frequency Interference (RFI)
Introduction to Radio Frequency Interference (RFI) With the plethora of wireless devices, increasing broadcast, communications, and other RF sources all competing for radio spectrum, the chances of radio frequency interference (RFI) will only increase. This article explains how to identify, characterize, and locate typical interfering sources. Categories of … [Read more...]
Does the Number of Bypass Capacitors for a Chip Matter?
How do you decide on the size of a bypass capacitor (or capacitors) for your project? Do you need multiple capacitors to bypass a specific chip? Are multiple value capacitors important for a given use? Do you subscribe to the old Wife’s Tail about having a couple capacitors a couple orders of magnitude different in value in parallel? Here is one take on the subject for you … [Read more...]
Emissions Test Facility – OATS vs SAC?
You’ve been tasked by management to build a new, from scratch, EMC test facility. Among other items, you need to decide between an Open Area Test Site (OATS) or an RF Semi-Anechoic Chamber (SAC). How do you decide? To someone who has been there, done that, the choice is clear, but what are some factors that might sway the decision one way or the other? Design of an … [Read more...]
Classical Shielding Theory vs. Near-Field Measurements
This article addresses the fundamental concepts underlying the classical shielding theory based on Schelkunoff’s equations [1]. In order to assess the applicability of these equations, an understanding of their origin, assumptions made in their derivations, and their limitations, are needed. This tutorial article addresses each of these points. The goal is not to show the … [Read more...]
What You See With Near Field Probes
In EMI/EMC troubleshooting, near field probes (NFPs) are great tools. Let's review how to understand what you really see at the screen of your instrument with a magnetic near field probe. EMI/EMC problems (radiated and conducted emissions) are usually related with current in your circuits: high frequency currents (i.e. high di/dt currents) are responsible of radiation from … [Read more...]
What is the Number One Item That Causes EMC Problems at the Board Level?
There are many “rules” for laying out a printed wiring board (PWB) to minimize generation of EMI from a board. These cover a wide range of issues that are important. Some more than others, but all can be important. But, if you were to ask what the number one item on the hit parade would be, what would you say? What are the important factors to consider when laying out a … [Read more...]
Tips for Writing Technical Articles for Magazines
Why write? Pride – To see your work in print is a just reward for a creative person. We all have a built-in desire to be creative and to be recognized for that creativity. Contribution – Well-written technical articles contribute to the total body of knowledge for the engineering community and will potentially help many engineers. Articles do not need to be detailed … [Read more...]
- « Previous Page
- 1
- …
- 6
- 7
- 8
- 9
- 10
- …
- 16
- Next Page »
