Harwin Gecko-MT 1.25mm pitch Mixed Layout Connectors Connect with confidence with Harwin’s Gecko-MT range; the smallest and lightest mixed-layout connector available for high-reliability applications. The Gecko-MT range combines the 1.25mm pitch Gecko signal connector system with mixed technology layouts, which adds 10A power contacts to the range, providing additional … [Read more...]
Antennas
- Free EMC Formulas & Equations: dBm, Volts, Watts Conversion
- Free EMC Formulas & Equations: Antenna Factor and Gain Calculations
- Free EMC Resource: VSWR vs. Return Loss Cheat Sheet
- Free Article: The Importance of Antenna Beamwidth in RF Testing
- Free Article: 4 Reasons To Get A Bilogical Antenna First For Device Testing
An Isotropic Probe for Radiated Susceptibility Measurements from 10kHz to 18GHz and 5V/m to 220V/m
Abstract: Isotropic probes are available for radiated susceptibility test level measurements from 100kHz to 6GHz, 2MHz to 18GHz, 2MHz to 40GHz and 2MHz to 60GHz. For MIL-STD-461 and DO-160 testing a frequency range of 10kHz to 18GHz would be better and a possible solution is presented here. Introduction The probe described in this paper has three separate sections, … [Read more...]
Review: EMI Devices Harmonic Comb Generator
Harmonic comb generators are handy tools for validating open area test sites or semi-anechoic chambers and I've written extensively on how to use these for various other applications (see References). Harmonic comb generators produce a range of narrow band harmonics that are typically very stable in amplitude and frequency. One of the major uses is to position one in place … [Read more...]
Risks Associated with EMC and EMI – Don’t get Confused!
There are many kinds of risk For example: the risk of being late for an appointment; the risk of buying a lottery ticket but not winning a prize; the risk of designing and manufacturing a new product that might not sell well enough, etc. The above are examples of non-safety-related risks, but safety-related risks also exist. EMC1 Risk Management (or, the Risk Management … [Read more...]
A Simple Method for Estimating Radiated Emissions – Part 2
I recently published this blog, detailing a simple proven method for estimating the radiated E field with specified test setup. As a result, I received the following feedback... 'This model is wrong for equipment tested over a ground plane as described. The complex correct transmission line model (less the ground plane) is given by Balanis, and a simpler but accurate … [Read more...]
A Simple Method for Estimating Radiated Emissions
A simple method for estimating radiated emissions I recently received the following question: How to calculate the radiated E field with following test conditions with an antenna placed 1 meter away from the test setup?: A commercial equipment under test with metal housing Equipment placed on the grounded metallic table/plane LISN installed (and also placed … [Read more...]
Comparison of PWM VFDs versus Resonant Link Converters – Part 2
In Part 2 of this blog, the harmonic current distortion of a typical Variable Frequency Drive (VFD) is discussed, as well the possible solutions to the problems that this causes. Active Front End or (AFE) units are also discussed and some of the issues that they themselves … [Read more...]
Comparison of PWM VFDs versus Resonant Link Converters – Part 1
AC variable frequency drives (VFDs) have been in existence in a number of forms since the early 1970s. In the early 1980s the “pulse width modulated” (PMW) VFD versions began to appear. This form of motor control produced less motor rotor and stator harmonic heating and delivered smoother torque control at slow motor speeds. Thirty years on PWM VFDs are still the most … [Read more...]
Interstate Connecting Components (ICC) Introduces BHA PTFE-Plated M28876 Connectors from Amphenol Fiber Systems
Interstate Connecting Components, a division of Heilind Mil-Aero and leading distributor of military-aerospace connectors and accessories, is now offering M28876 circular fiber optic connectors with black hard anodized (BHA) PTFE (polytetrafluoroethylene) plating. The connectors are precision-engineered by Amphenol Fiber Systems International, a leading manufacturer of fiber … [Read more...]
TMD USA Wins Major Defense Contract For Traveling Wave Tube Amplifiers in A Mission-Critical Surveillance Role
Now part of Communications & Power Industries (CPI)) has won a large defense contract for traveling wave tube amplifiers (TWTAs) for use in a radar unmanned aerial vehicle program. Valued in excess of $2.5 million, the contract was awarded by a prime contractor under the terms of a competitive bid. Said Tom Curtin, vice president, sales and business development, TMD … [Read more...]
- « Previous Page
- 1
- 2
- 3
- 4
- …
- 57
- Next Page »