Figure 1: Tu-Pod in Space (Courtesy Amin Djamshidpour, Co-Founder Teton Aerospace) CubeSats are relatively inexpensive when compared to traditional vehicle-size satellites. Since their inception, CubeSat spacecraft have shown functional success rates ranging from 40% to 75% for launch and deployment phases. According to the International Journal of Aerospace Engineering, … [Read more...]
Creative Materials Inc. Announces the Release of Multi-Purpose Conductive Epoxies
Creative Materials Inc. Proudly announces its series of multi-purpose conductive epoxies that combine flexibility with fine-line precision and extreme durability. Both products reflect the continuous effort to meet evolving customer needs through innovation, performance, and quality. Products: 126-40(SD) and 126-40(SP) Product Descriptions: 126-40(SD) is a single … [Read more...]
IoT Systems with mmWave Sensors
One of the most common applications of Internet of Things (IoT) devices is sensing, followed by transmission of raw data back to a base station or server for storage and further analysis. The most common of these sensing tasks seems to be environmental sensing, such as monitoring gas concentrations, temperature, humidity, etc. These devices are so ubiquitous that they … [Read more...]
EMI Basics and Board Level Shielding Design
Introduction In today’s world full of digital electronic devices, electromagnetic interference (EMI) is a major concern in both military and commercial marketplaces. Electrical equipment can become susceptible to these undesirable emissions and malfunction due to their presence. The simplest and most cost-effective method for reducing EMI is to first attack it at the board … [Read more...]
Static Control Resilient Flooring Qualification Procedures Ensure Space and Defense ESD Compliance Pt. 2
This article is the second and final part of Static Control Resilient Flooring Qualification Procedures Ensure Space and Defense ESD Compliance. Read Part 1 here. ANSI/ESD STM97.2 This critical standard test method attests to the static control resilient flooring’s ability to minimize charge buildup and provides the user with traceable data to assign a voltage flooring … [Read more...]
When Do You Need Low-Dk PCB Laminates?
Designers looking to build more advanced systems operating at higher data rates and bandwidths tend to rely on materials with low dielectric constant values, i.e., low-Dk materials. It has gotten to the point where every high-speed PCB design guide implies that high-speed and RF designs will not function without a low-Dk material like Rogers or Arlon. The reality is that … [Read more...]
Static Control Resilient Flooring Qualification Procedures Ensure Space and Defense ESD Compliance Pt. 1
Due to the rapid densification of ESD sensitive devices (ESDS), static control resilient flooring (ESD flooring) has found its way into FAA towers, operating room theatres, MRI/CT scan flooring areas, aircraft terminals, IT data centers, Navy ships, space & defense flight lines, call centers, medical device manufacturing, pharmaceutical delivery and the … [Read more...]
Plugging into a Power Source 93 Million Miles Away
Harwin Gecko-MT 1.25mm pitch Mixed Layout Connectors Connect with confidence with Harwin’s Gecko-MT range; the smallest and lightest mixed-layout connector available for high-reliability applications. The Gecko-MT range combines the 1.25mm pitch Gecko signal connector system with mixed technology layouts, which adds 10A power contacts to the range, providing additional … [Read more...]
An Isotropic Probe for Radiated Susceptibility Measurements from 10kHz to 18GHz and 5V/m to 220V/m
Abstract: Isotropic probes are available for radiated susceptibility test level measurements from 100kHz to 6GHz, 2MHz to 18GHz, 2MHz to 40GHz and 2MHz to 60GHz. For MIL-STD-461 and DO-160 testing a frequency range of 10kHz to 18GHz would be better and a possible solution is presented here. Introduction The probe described in this paper has three separate sections, … [Read more...]
EMC Confidence Checking
I was recently working with a manufacturer of stand-alone ticket machines, who had big problems with Ethernet-related emissions. Long story short – it was the Ethernet hub they had incorporated in their machine. They had assumed that all CE-marked Ethernet hubs would be equally good for EMC, and they had several different types lying around their design department. We tested … [Read more...]
- 1
- 2
- 3
- …
- 22
- Next Page »